| Mini Panel |
|
The NCE Mini-Panel uses DCC technology to make control panel wiring much easier and effective. If you are using or plan to use stationary decoders or DCC accesories, the Mini-Panel is a must. |
- Save up to 50% of the normal control panel wiring required.
- Use one button to control multiple switches or macros on your NCE DCC.
- Up to 30 pushbuttons, toggle switches, block detectors, etc. can be connected for control of turnouts, signals and other devices.
- Easy connections, convenient screw terminals.
- Easy programming, just plug in an NCE ProCab.
- Simple hook up, one Cab Bus connection and 2 wires for each pushbutton or other input device.
- Can be used to perform simple automatic train control and other layout automation tasks.
- Control any turnout, accessory from a button anywhere on the layout.
DCC TrainShop $42.95
List: $49.95 |
|
| Decoder Tester |
Perfect
companion to DCC installation and operation, the decoder tester
works with ANY DCC decoder. Test for motor forward
and reverse, functions 0F, 0R, 1, and 2.
DCC TrainShop $19.95
List: $24.95 |
|
| BD20 |
Detects
DCC current being drawn in a block. Connects to AIU01 or most
commercial signal systems.
DCC TrainShop $13.95
List: $14.95 |
|
| AIU01 |
The
Auxiliary Input Unit provides connection of block occupancy
detectors, switch position relays, etc. for purposes of
signaling and/or computer control of your layout. Simply plugs
in to the Cab Bus.
DCC TrainShop $39.95
List: $49.95 |
|
| SIG4 |
Operates
4 signal heads. Can be used with Cab control, Computer control
or Interlocking and CTC.
DCC TrainShop $46.95
List: $59.95 |
|
| Packet
Analyzer |
Use
the NCE Packet Analyzer and your computer to view DCC packets
being sent by any DCC system. Selectively filter out idle,
reset, accessory, function and/or speed packets. Information can
be displayed in hexidecimal or our special "verbose"
mode that makes it easy to decipher track activity. Requires PC,
Mac or Linux computer with terminal program and 9 pin serial
cable. Can also be used to monitor NCE Cab Bus activity.
DCC TrainShop $39.95
List: $49.95 |
| Power
Cab USB Interface |
Add
this USB computer interface for computer programming and/or
operation of your Power Cab equipped layout. Requires USB cable,
computer and railroad computer program such as JMRI Decoder Pro
and Panel Pro. Can be used with the PH Pro and PH10 systems.
HOWEVER, with the PH systems you can only RUN or OPERATE
railroads with it. You can not use the USB Interface to Program
decoders.
DCC TrainShop $39.95
List: $49.95 |
|
| Auto-SW |
The
Auto-SW adds a separate program track to your Power Cab system.
Prevents accidental programming of ALL locos on your track when
using Program Track mode. Automatically disconnects your main
line when in Program Track mode (does not affect Program on
Main). Compatible with ALL DCC systems such as Digitrax™ Big
Boy, Empire Builder and Bachmann EZ-Command.
DCC TrainShop $19.95
List: $24.95 |
|
| UTP |
This is
our lowest cost, easiest to use cab bus panel. All four RJ-12
jacks are wired in parallel for easy plug and play use. This
board also provides a convenient point to add additional 12 Volt
cab bus power, just plug in a 12 Volt "wall wart"
power supply. Shown with the included 1/16" thick aluminum,
black anodized fascia plate.
DCC TrainShop $15.95
List: $19.95 |
|
| UTP-DIN |
Recommended
for large club installations. This panel combines low cost with
rugged DIN jacks for long life. RJ-12 jacks provided on back for
easy plug and play installation. Solder holes also provided for
high reliability hard wired installation. Includes a 1/16"
thick aluminum, black anodized fascia plate.
DCC TrainShop $15.95
List: $19.95 |
|
| PCP |
Add
a separate PCP panel to operate your Power Cab in other places
or on other layouts. Use the P114 and you will only have to move
the Power Cab.
DCC TrainShop $19.95
List: $24.95 |
|
